What are the production methods and basic steps of industrial sand table model? The production personnel of Zibo model company answers for you:

　　沙盤模型制作

　　Sand table model making

　　1、設置沙盤：先將沙盤框放置穩妥,盡量使沙盤的方位和現地一致,再鋪上3-5厘米厚,濕度適當?shù)纳惩?并用木板刮平壓緊,作為低處等高線的平面,然后打上和地形圖相應的方格,在沙盤框周圍注記相應的編號.

　　1. Setting up sand table: first place the sand table frame stably, try to make the direction of the sand table consistent with the site, then pave 3-5cm thick sand soil with appropriate humidity, and use the wood plate to scrape flat and compact, as the plane of the contour line at the low place, then mark the corresponding grid with the topographic map, and mark the corresponding number around the sand table frame

　　2、堆積地貌

　　2. Cumulate landform

　　(1)依照方格將地形圖上已選定的低處等高線,能控制地貌基本形狀的等高線,以及山頂,鞍部,山腳,傾斜變換點和江河等到的位置畫到沙盤面上.

　　(1) According to the grid, the selected contour lines at the lower part of the topographic map, the contour lines that can control the basic shape of the landform, as well as the positions of the top of the mountain, saddle, foot of the mountain, change point of inclination and rivers, are drawn on the sand table surface

　　(2)將計算好的山頂,鞍部,山腳,傾斜變換點和江河彎曲部等起伏明顯和點,分別插上竹簽.竹簽的高度,為該點在沙盤上的高度加上底層沙土的厚度.

　　(2) The height of the bamboo stick is the height of the point on the sand table plus the thickness of the underlying sand

　　(3)在低處等到高線范圍內,以竹簽和等高線為依據,先堆出山頂,鞍部,山背等的概略形狀作為骨干,再修整其他部分.如沙盤較大,可分片堆積,先堆積進出困難處,后堆積進出方便處.堆積時,應隨時對照地形圖,以正確顯示地貌的起伏狀況,并應隨時將沙土壓緊,以免崩塌變形.如有較大的江河,湖泊,應在修整地貌時一并挖成.堆積完畢,應作全面檢查和修整,并從高到低逐層撒上與地面顏色相符的鋸末(或噴以顏色).

　　(3) In the range from low place to high line, based on bamboo sticks and contour lines, pile out the top of the mountain, saddle, back of the mountain as the backbone, and then trim other parts. For example, if the sand table is large, it can be stacked in pieces, first in and out of the difficult places, and then in and out of the convenient places. When stacking, it should be compared with the topographic map at any time to correctly show the relief of the landform, and the sand and soil should be compacted at any time, In order to avoid collapse and deformation, if there are large rivers and lakes, they should be excavated together when trimming the landform. After stacking, they should be comprehensively inspected and trimmed, and sawdust (or spray with color) matching with the ground color should be sprinkled layer by layer from high to low

　　3、設置地物：沙盤上的地物,如房屋,鐵路,橋梁,樹木和獨立地物等,多用相似的模型表示,公路和鄉村路用寬窄不等,顏色不同的紙(布條)表示;江河用藍色紙條或鋸末表示;樹林用小樹枝或綠色鋸末表示.地物的大小,應與水平比例尺相適應,關系位置要求正確.設置地物,應按水系,居民地,道路,樹林和獨立地物的順序進行設置.然后,在相應的位置上插上地名,江河名,山名和高程注記等紙牌.

　　3. Setting up features: features on the sand table, such as houses, railways, bridges, trees and independent features, are mostly represented by similar models. Roads and rural roads are represented by paper (cloth) of different width and color; rivers are represented by blue paper or sawdust; trees are represented by twigs or green sawdust. The size of the features should be adapted to the horizontal scale, and the relationship position requirements are correct. Setting up features, It should be set according to the sequence of water system, residential area, road, forest and independent features. Then, place names, river names, mountain names and elevation notes should be inserted in corresponding positions

　　4、設置戰術情況：戰術情況,通常根據預定的作戰方案或訓練想定,用制式的兵棋,臨時制作的隊標,隊號等進行設置.設置時,先設戰斗分界線,而后按先敵后我,由前沿到縱深的順序進行.如需顯示敵,我設防工程時,應先設置工作設施,后設置戰術情況.

　　4. Setting of tactics: the tactics are usually set according to the predetermined battle plan or training plan, using the standard war chess, temporarily made team mark, team number, etc. when setting up, the battle dividing line is set first, and then it is carried out in the order of first enemy, then us, from the front to the depth. If it is necessary to display the enemy, when we set up the defense project, we should first set up the working facilities, then set up the tactics

　　5、整飾上述各項工作完成后,應詳細對照檢查,并標明沙盤的名稱,指北箭頭和比例尺,需要時用線繩拉上坐標網。

　　5. After finishing the above work, it shall be checked in detail, and the name of sand table shall be indicated, the north arrow and scale shall be pointed out, and the coordinate network shall be pulled up with wire rope if necessary.

　　以上是關于工業沙盤模型的制作方法，由淄博模型公司友情分享，想要了解更多內容歡迎咨詢http://www.vozpt.com官網。

　　The above is about the production method of industrial sand table model, which is shared by Zibo model company. If you want to know more, please consult http://www.vozpt.com Official website.